All products must conform to NSF/ANSI standards 60 or 61, if available.
1.1. Fire Hydrants (Flushing Valves, AWWA C 502) (Pumper nozzle 5.25 inch, hose nozzle 2.5 inch, see COP Standard Details)
- a. Mueller Super Centurian 250
- b. American Darling B-84-B
- c. East Jordan Iron Works WaterMaster 5CD250
1.2. Fire Hydrant (Approved Paint Colors, shop primed, field painted)
- a. 6”, Glossy White Code No 225A120
- b. 8” Safety Orange Code No 225A122
- c. 12” John Deere Green Code No 225A133
- d. 16” and 20” John Deere Yellow Code No 225A138
- e. 22” and up Safety Red Code No 225A123
- f. Fire Hydrant Barrel Safety Blue Code No 225A120
1.3. Gate Valves (4” thru 12”) Non Directional Resilient Seated, Stainless Steel Bolts, mechanical joints only
- a. Mueller
- b. East Jordan
- c. American Flow Control
1.4. PVC Pipe (AWWA C900/905)
- a. All compliant manufactures
1.5. Ductile Iron Pipe and Fitting Restraints (AWWA 110/104)
- a. EBAA Iron Inc. MegaLug Mechanical Joint Restraint
- b. Ford – Uni-Flange
- c. Clow Corp. Super-Lock Joint
- d. American Cast Iron Co.
- e. US Pipe and Foundry Co.
- f. McWane Cast Iron Pipe Co.
- g. US Pipe and Foundry Co
1.6. HDPE Pipe for Water – DR 11/14, Blue Lines
- a. All compliant manufactures
1.7. Curb Stop (90 deg locking rings)
- a. Ford
- b. Mueller
- c. Jones
- d. McDonald
1.8. Service Saddle PVC pipe – full stainless or epoxy coated tapping saddle, wide stainless steel bands and hardware)
- a. Mueller
- b. Romac Series 101S
- c. Smith Blair
- d. Ford
1.9. Service Saddle - 16” and up PVC C 905, epoxy coated tapping saddle, dual wide stainless steel bands and stainless hardware.
- a. Mueller
- b. Smith Blair
- c. Romac Series 202S
1.10. Air Release Valve – 2”
1.11. Pumps (to be reviewed and approved prior to bid)
1.12. Combination Vacuum Relief Valves
- a. APCO Series
- b. Ga Industries
- c. Val-Matic
- d. ARI
1.13. Pressure Reducing Valves
1.14. Valve Boxes and Meter Boxes
- a. Single service, NDS 1300
- b. Double Service, NDS 1600
- c. Bass and Hays Foundry Inc
1.15. Pipe Casing Spacers (SS) & End Seals for Bored Crossings
- a. Pipeline Seal and Insulator
- b. CCI Pipeline
1.16. Tapping Sleeves (Stainless Steel)
- a. JCM
- b. 12” or smaller, Romac
- c. Smith Blair
1.17. Polyurethane Wrap
- a. Polyken No 900
- b. Scotchwrap No 50
1.18. Service Tubing (3/4" - 2")
- a. CTS-SDR9
- b. Rehau Municiplex
1.19. Ground Storage Tanks
- a. Concrete
- b. Welded Steel
1.20. Backflow Prevention
- a. Watts LF8004FR
- b. Wilkins 420XL
- c. Wilkins 720A or equal
1.21. Reduced Pressure Backflow
- a. Febco No LF825Y
- b. Watts LF909
- c. Wilkins 975XL2 LF4000B or equal
- d. ParkUSA RPDAA
1.22. Double Check Assembly
- a. Febco LF850
- b. Watts LF007
- c. Apollo DC4ALF
- d. Ames LF2000B or equal
- e. ParkUSA DDBP
1.23. Waterline Pressure Sensor
- Approved Equipment:
- PR32iA-M1V-200-030-EAC-BMI – RTU and Pressure Sensor
- A-CBA-LTE – Burial Antenna
- 68886-1001 – Telog Remote Monitoring Subscription
- Activation – Part number required to activate the unit at time of shipment
- Installation and Technical Requirements:
- The pressure sensor must be delivered with the pressure transducer preconnected to the data recorder and fully calibrated.
- A burial-grade antenna is required. Meter boxes must be plastic or concrete — metal enclosures are not permitted due to interference with signal transmission.
- The data recorder is typically enclosed in a meter box for protection and accessibility.
- The pressure tap must be installed directly on the main waterline, not from a hydrant connection.
1.24. Sampling Station
- a. Mueller 16.12 Hydro-Guard Sampling Station
- i. Base Part # BSS01
- ii. Pipe Material – Stainless Steel
